Submarine Cable Test Equipment
Submarine Cable Survey System Model 5930
Features
- Accurate Cable Burial Depth Measurement
- Computer Interface
- Integral Test Function
- Divers Audio Output of Signal Strength
- GPS Data Input
- Wide Frequency Range
- Spectrum Analyser Function
- Oscilloscope Function
- Rated to 50 metres water depth
- Two Probe Inputs
For more information about this product contact Tinsley
|
|
|
The Tinsley Submarine Cable Survey System is designed for use by divers working in areas where it may not be practical to use an R.O.V.. With a low frequency electroding tone applied to the cable, the system can be used to locate cables buried beneath the seabed and to establish their burial depth.
The system consists of a hand held Sensing Unit (type 5931) that is designed to be easily manoeuvred whilst under water. An audio output to the diver allows the Sensing Unit to be positioned at a point with the highest signal level. This corresponds to a point directly over the cable being surveyed. Once the cable is precisely located the Sensing Unit is placed on the seabed at that point and a measurement of Burial Depth made.
The Sensing Unit is connected to the shipboard Display Unit (Type 5930) via an umbilical cable. The Display Unit uses microprocessor technology to compute the data received from the sensor and to display the information as the burial depth of the cable.
Many special functions are incorporated within the Display Unit. It features a Spectrum Analyser that is used to identify any areas of the frequency range for the Survey System that exhibit a particularly high level of electromagnetic interference. The use of this frequency can then be avoided whilst cable surveying in that particular geographical location.
Digital filtering of the input signal is used to ensure the instrument displays clear and unambiguous results. Electronic tuning enables the system to precisely detect the frequency of the tone applied to the cable.
The Single Sensor probe Model 5932 is used for fast location of cables. It does not give burial depth measurement.
Any standard Electroding Generator operating within the frequency range 16 to 100Hz may be used with the system. Typically the Tinsley Model 5915 or the electroding function of the Tinsley Model 5910 Submarine Cable Test Set could be used to energise the cable.
Ordering Information
| |
|
|
|
5930 |
Dual input Surface Display Unit |
5931 |
Triple Sensor Frame for Cable Detection and Burial Depth Measurement |
5931E/2m |
Bone Conductor Earphone with 2 metre Lead |
5931C1/50 |
50 metre Underwater Umbilical Cable |
5931C1/100 |
100 metre Underwater Umbilical Cable |
5931C2/5 |
5 metre Deck Cable |
5931C2/10 |
10 metre Deck Cable |
5932 |
Single Sensor for Cable Detection |
 |
Triple Sensing Unit Model 5931
Gives cable location and burial depth. |
| |
|
 |
Single Sensor Unit Model 5932
For cable location only. |
|
|
Specifications
See the table below for a run-down of this product's specifications.
Burial Depth Accuracy
|
Basic Accuracy ±5% of measurement
|
Burial Depth Range
|
0.1 to 3 metres
|
Temperature Range
|
In Use 0°C to 45°C
|
Storage -10°C to 60°C
|
Temperature Coefficient
|
0.5% / °C
|
|
Dimensions
|
Sensor Unit
|
50cm x 40cm base 50cm high
|
Display Unit
|
36cm wide x 40cm depth x 20cm high
|
Weight
|
Sensor Unit
|
7kg in air 5kg in water
|
Display Unit
|
11kg
|
Sea Cable
5931C1/50m
5931C1/100m
|
Length
|
50 metres or 100 metres
|
Diameter
|
10.5mm
|
Colour
|
Yellow
|
Mechanical Strength
|
Up to 100kg. Peak.
|
Connectors
|
Underwater mating moulded at both ends.
|
Deck Cable
5931C2/50m
5931C2/100m
|
Length
|
5 metres or 10 metres
|
Diameter
|
10.5mm
|
Colour
|
Yellow
|
Mechanical Strength
|
Up to 100kg. Peak.
|
Connectors
|
Underwater mating moulded at one end - IP63 type fitted at the other
|
Bone Conducting Earphone
5931E/2m
|
Cable Length
|
2 metres
|
Cable Diameter
|
5mm.
|
Colour
|
Black
|
Mechanical Strength
|
Up to 10kg Peak
|
Connectors
|
Moulded underwater mating
|
Display Unit 5930 Special Features
|
Computer Interface
|
RS232 - RS485
|
GPS Data Input
|
Ships GPS data can be input and recorded with burial depth measurements
|
Data Recording
|
Burial depth information can be stored to a file for later downloading
|
Test Oscillator
|
An integral Test Oscillator allows the system to be tested before immersion
|
Display
|
Daylight readable TFT colour
|
Diver Audio Mute
|
Audio signal to diver can be muted from the Display Unit in an emergency
|
For more information about this product contact Tinsley
|
